دستگاه چاپ فلکسو Bobst 203 A-Matic

A) Technical Data

Sheet width (including waste, in running direction): min. 600 mm, max. 2032 mm

Sheet width (including waste, in running direction): min. 600 mm, max. 2032 mm

Sheet length (including waste, in running direction): min. 520 mm, max. 1270 mm

Sheet length (including waste, in running direction): min. 520 mm, max. 1270 mm

Max. die-cut format (with front waste): 2032 mm × 1245 mm

Max. die-cut format (with front waste): 2032 mm × 1245 mm

Material thickness: 1.0 – 9.0 mm

Material thickness: 1.0 – 9.0 mm

Gripper margin (adjustable): 15 +3 / -6 mm

Gripper margin (adjustable): 15 +3 / -6 mm

Standard side trim: 10 mm each (9 mm with vertical flute, 8 mm with horizontal flute)

Standard side trim: 10 mm each (9 mm with vertical flute, 8 mm with horizontal flute)

Standard rear trim: 10 mm

Standard rear trim: 10 mm

Max. speed: up to 5,500 sheets/hour (depending on job)

Max. speed: up to 5,500 sheets/hour (depending on job)

Max. die-cutting force: 550 tons

Max. die-cutting force: 550 tons

Die rule height: 23.8 mm

Die rule height: 23.8 mm

Waste allowance in running direction: 15+10 = 25 mm

Waste allowance in running direction: 15+10 = 25 mm

Waste allowance across running direction: vertical flute 16 mm, horizontal flute 18 mm

Waste allowance across running direction: vertical flute 16 mm, horizontal flute 18 mm
B) Equipment

Prefeeder Dynaload


Max. pile height (without pallet): 1900 mm


Max. stack weight: 1300 kg



Prefeeder Dynaload

Max. pile height (without pallet): 1900 mm

Max. pile height (without pallet): 1900 mm

Max. stack weight: 1300 kg

Max. stack weight: 1300 kg

Die-Cutter SPO 203 A-Matic


Tool pre-mounting stand with second chase


Die-cutting tool top, bottom with hard thick counter plate plus 1 mm medium-hard plate


Centerline II system



Die-Cutter SPO 203 A-Matic

Tool pre-mounting stand with second chase

Tool pre-mounting stand with second chase

Die-cutting tool top, bottom with hard thick counter plate plus 1 mm medium-hard plate

Die-cutting tool top, bottom with hard thick counter plate plus 1 mm medium-hard plate

Centerline II system

Centerline II system

Blank separator (crosswise to running direction) Dynabreak S1


Variable pile height: min. 50 mm, max. 250 mm


Max. separations: 9 (10 blanks)


Min. separation distance: 150 mm (250 mm)


Trials: up to 6 blanks 140 mm, preferably 150 mm; 7–9 blanks 150 mm, preferably 160 mm



Blank separator (crosswise to running direction) Dynabreak S1

Variable pile height: min. 50 mm, max. 250 mm

Variable pile height: min. 50 mm, max. 250 mm

Max. separations: 9 (10 blanks)

Max. separations: 9 (10 blanks)

Min. separation distance: 150 mm (250 mm)

Min. separation distance: 150 mm (250 mm)

Trials: up to 6 blanks 140 mm, preferably 150 mm; 7–9 blanks 150 mm, preferably 160 mm

Trials: up to 6 blanks 140 mm, preferably 150 mm; 7–9 blanks 150 mm, preferably 160 mm

Blank separator (lengthwise to running direction) Dynabreak S2


Variable pile height: min. 50 mm, max. 250 mm


Max. separations: 5 (6 blanks)


Min. separation distance: approx. 150 mm (from trials)



Blank separator (lengthwise to running direction) Dynabreak S2

Variable pile height: min. 50 mm, max. 250 mm

Variable pile height: min. 50 mm, max. 250 mm

Max. separations: 5 (6 blanks)

Max. separations: 5 (6 blanks)

Min. separation distance: approx. 150 mm (from trials)

Min. separation distance: approx. 150 mm (from trials)
C) Tolerances

In addition to tolerances from sheet manufacturing (width and length variation) and printing (if applicable), die-cutting introduces the following tolerances, based on optimal sheet quality.

In addition to tolerances from sheet manufacturing (width and length variation) and printing (if applicable), die-cutting introduces the following tolerances, based on optimal sheet quality.

Strong warping, curvature, or non-square cuts will increase tolerances, especially if they vary within a job.

Strong warping, curvature, or non-square cuts will increase tolerances, especially if they vary within a job.

Best results, including for skip-feed jobs, are achieved with vertical flute running direction.

Best results, including for skip-feed jobs, are achieved with vertical flute running direction.
Tolerance values:

In running direction: ±0.25 mm (vertical flute), ±0.50 mm (horizontal flute)

In running direction: ±0.25 mm (vertical flute), ±0.50 mm (horizontal flute)

Side tolerance (crosswise): ±0.75 mm (vertical flute), ±0.75 mm (horizontal flute)

Side tolerance (crosswise): ±0.75 mm (vertical flute), ±0.75 mm (horizontal flute)
Conditions for tolerances to apply:

Machine and tooling manufactured according to BOBST-ABC

Machine and tooling manufactured according to BOBST-ABC

Machine maintenance per BOBST documentation

Machine maintenance per BOBST documentation

Processing of corrugated board per VDW standard

Processing of corrugated board per VDW standard

For laminated material, sheets may overhang max. 3 mm

For laminated material, sheets may overhang max. 3 mm

For printed sheets, format must be 50% of maximum format

For printed sheets, format must be 50% of maximum format

Consistent machine operation is required; first and last ten sheets (with all blanks) are excluded from measurement

Consistent machine operation is required; first and last ten sheets (with all blanks) are excluded from measurement
Category: Flatbed Die Cutter